Ich habe auf meinem Lenovo Tablet vor ca. 2 Wochen den RigManager installiert und dann gleich die WLAN-Verbindung ausprobiert. Das funktionierte auf Anhieb. Seit dem habe ich das Tablet mit dem RigManager nicht wieder benutzt, heute aber wieder versucht. Jetzt sehe ich wohl, dass mein Stage-Gerät bei angekreuztem "Wifi Enable" meine Fritzbox sich als Router gemerkt hat. Der Android RigManager sucht aber vergeblich nach dem Stage Netzwerkgerät. In der Fritzbox taucht der Stage auch nicht als aktives Gerät auf. Der Versuch, per WPS eine Verbindung neu zu erzeugen, ist auch ohne Erfolg. Dabei ist mir aufgefallen, dass der Button auf dem Stage, der WPS ausführen soll, nicht so hell leuchtet wie der Button für "Wifi Enable"; er ist aber auch nicht dunkel wie bei "Access Point Mode". Der Button "Home Network Mode" leuchtet dagegen voll, lässt sich aber auch nicht deaktivieren(?).
Weiterer Hinweis: in der Fritzbox hatte ich den Namen des Eintrags für den Stage geändert, von "My Profiler" auf "Kemper Profiler". Ich habe aber heute nach dem Connect-Misserfolg das Netzwerkgerät aus der FritzBox gelöscht und wollte mit WPS die Verbindung neu aufbauen. Die Fritzbox meldet übrigens keine Fehler im Log.
I installed the RigManager on my Lenovo tablet about 2 weeks ago and then immediately tried out the WLAN connection. It worked straight away. I haven't used the tablet with RigManager since then, but I tried again today. Now I can see that my stage device has remembered my Fritzbox as a router when "Wifi Enable" is selected. However, the Android RigManager searches in vain for the Stage network device. The Fritzbox does not show the Stage as an active device either. The attempt to create a new connection via WPS is also unsuccessful. I noticed that the button on the stage that is supposed to perform WPS does not light up as brightly as the button for "Wifi Enable"; however, it is also not dark as with "Access Point Mode". The "Home Network Mode" button, on the other hand, is fully lit, but cannot be deactivated(?).
Another note: I had changed the name of the entry for the stage in the Fritzbox from "My Profiler" to "Kemper Profiler". However, I deleted the network device from the FritzBox today after the connection failure and wanted to re-establish the connection with WPS. Incidentally, the Fritzbox does not report any errors in the log.
I installed the RigManager on my Lenovo tablet about 2 weeks ago and then immediately tried out the WLAN connection. It worked straight away. I haven't used the tablet with RigManager since then, but I tried again today. Now I can see that my stage device has remembered my Fritzbox as a router when "Wifi Enable" is selected. However, the Android RigManager searches in vain for the Stage network device. The Fritzbox does not show the Stage as an active device either. The attempt to create a new connection via WPS is also unsuccessful. I noticed that the button on the stage that is supposed to perform WPS does not light up as brightly as the button for "Wifi Enable"; however, it is also not dark as with "Access Point Mode". The "Home Network Mode" button, on the other hand, is fully lit, but cannot be deactivated(?).
I installed the RigManager on my Lenovo tablet about 2 weeks ago and then immediately tried out the WLAN connection. It worked straight away. I haven't used the tablet with RigManager since then, but I tried again today. Now I can see that my stage device has remembered my Fritzbox as a router when "Wifi Enable" is selected. However, the Android RigManager searches in vain for the Stage network device. The Fritzbox does not show the Stage as an active device either. The attempt to create a new connection via WPS is also unsuccessful. I noticed that the button on the stage that is supposed to perform WPS does not light up as brightly as the button for "Wifi Enable"; however, it is also not dark as with "Access Point Mode". The "Home Network Mode" button, on the other hand, is fully lit, but cannot be deactivated(?).
Another note: I had changed the name of the entry for the stage in the Fritzbox from "My Profiler" to "Kemper Profiler". However, I deleted the network device from the FritzBox today after the connection failure and wanted to re-establish the connection with WPS. Incidentally, the Fritzbox does not report any errors in the log.
Another note: I had changed the name of the entry for the stage in the Fritzbox from "My Profiler" to "Kemper Profiler". However, I deleted the network device from the FritzBox today after the connection failure and wanted to re-establish the connection with WPS. Incidentally, the Fritzbox does not report any errors in the log.
Translated with DeepL.com (free version)