Looking forward to inserting some Liquid into my Stage!
Posts by spikey
-
-
Are reverb discussions wet or dry?
-
Thanks, guys glad to be back!
-
Yep, it was in the pedal settings just like you guys said!
THANKS!
-
Hey guys,
So I set my gain up from lower to higher and when I hit the button (bottom 1-5) on the stage it also takes my wah pedal (when it is on) from low to high too. Wah is set to heel down = off. The Mission expression pedal is in #2.
How do I un-attach the Wah pedal from the gain morph on the button?
-
I had one of those PortaStudios!!!
-
My new[Blocked Image: http://i.imgur.com/s2GVnnN.jpg]">Sire
-
full? Geese, add the ones you actually use or like and add to the favourite file and there is an option to delete all but favourites.
I didnt know that! Thanks for the tip! Im currently examining each and every profile as OCD requires. I should be done around Christmas 2029.
-
Ok, no more Neil Diamond stuff I promise lol.
Im a returning Kemper user, this time a new "Stage" owner, and in the process of getting all the cables ran and sorted in the studio.
Just wanted to say Hi and looking forward to reading, talking, and learning about my new Kemper Stage.
-
Im 65 & Love Reverb! Oh, yea. But that's not always on the menu anymore like it was. And it depends on the room/setting too. I'll always sprinkle a little on my tunes if recording, however. To each their own and YMMV.
-
The Kone functionality (whether imprint or FRFR mode) is only available on the Monitor Out/Speaker Out. Main Outs never get the Kone functions.
DING! It finally made sense to me. THANK YOU! I needed that info...
-
If you want to run it in full range mode I would think the Powercab will be just as good. If you want to run imprints and have them sound like the real speaker the Kabinet is really the only option.
One way to test how the Kone setting in the KPA works to adjust the Kabinet speaker to be flat response could be to do as follows:
Set Main Out and Monitor Out to Master Mono.
Link Main Out and Monitor out to your audio interface and listen to the results through headphones or studio monitors.
Balance the levels from each output to be the same.
Make sure that Kone unticked in the Output Menu and compare the two signals. They should be identical.
Next tick Kone in the output menu and make sure Monitor Cab Off is unticked in the Output Menu. This puts the KPA into full range mode and adjusts the eq internally to make the Kone response as flat as possible.
Now compare the Main Outs to the Monitor Out. They will be wildly different. This shows just how much eq adjustment is being applied in the profiler to get the speaker neutral to start with. All imprints assume that the speaker being used requires the same eq adjustment before adding the imprint itself. Therefore, if the speaker in an alternative full range cabinet is used it will have its own internal eq adjustments to compensate for the speaker's response AND will then have the Kone compensation applied on top of this. The results will be unpredictable at best.
So reading this, we can set the "Main" outputs for the Kone speaker pair only, and then set the "Monitor" outs for the FRFR? Is that correct?
Asking because sometimes I want to run the Kone Pair for jamming, and other times I will run the FRFR for recording...
Edited: Sorry it's been a while and I forgot- Also found this- Monitor Out and Direct out issue?
So assuming we can run both sets at the same time, is there any use/advantage in running both at the same time tone-wise?
-
Speak for yourself.
I have to, you won't lol... Never saw anyone so against something they know so little about.
-
3ms is as if you were one meter away from your speaker. I can't feel or hear any latency at 3ms.
Here's another flat statement, short of being Superman, neither can anyone else...
-
For the record I didn't mean this is the wrong part of the Kemper forum to discuss. I meant that this sort of thread about a competing product is likely to get ugly. I could be wrong...
Too late it already got ugly, but thanks for saying that. The thing is we should be able to have a conversation about these products without blowing snot bubbles at each other (me included) or predicting doom and gloom about anything when we really don't know the outcome. And finally (no pun intended) the amusing part for me is I'm not even getting a QC now (I have none on pre-order), but I believe it's alright to discuss it here in the proper thread, and obviously so does Mr. Kemper. And +1000 for that.
-
I find it disturbing and annoying that you act like the forum police.
Yes, calling a spade a spade will cause that response... Even when the subject matter is "on topic" within the thread it resides in. Of course, that's my opinion too, so please "like lightbox suggests" look that up as well lol...
-
Maybe let’s wait for the product to be released and then consider allegedly unjustified critique to be insults?
Why? You didnt.
-
Very nice info- Thanks!
-
-
TY again Thumas!!!