Posts by Nuno Conde

Quote from Roeffel

Did you try changing the ground lifts ?

Raf

Hi Raf,
Yes I did (nothing changed )

Thanks for your help!

Nuno

I Just bought an Swiff ws-50, and it adds a lots of noise on my Kemper (Toaster amp version):

If no cable is connected to Kemper it makes noise, If I connect a guitar cable it turns down, but If I connect my new Swiff WS-50 wireless, the noise continues.

Does anybody can explain me this, please? And someone can help me with a hint to reduce/eliminate this noise with the Wireless?

Thank you in advance

Nuno

I have the same issue. 10.1 not fixed it

And the level is always lower on LP than the "original"

good afternoon. I've been looking here on the forum, but I haven't found any similar question. I tried to upgrade some old presets to liquid profiles. however the new ones are all at a lower volume. shouldn't be supposed, right? what am I doing wrong? can you help me please? thank you very much

Nuno

HI,

Thanks for your help, but could you explain your achieve, please?

Nuno

Quote from V8guitar

My "tester" is the intro to Highway to hell to get that silence inbetween the chords...even with relatively low gain on a valve amp there is often some hiss, but with a gate set just right its fab

Thanks for the tip! You rock

Quote from diogofis

Hi, Nuno. They are all showing up for me. Look for Diogo F. de Agui in the Rig Manager.

Thanks Diogo! My RM was sorted by upload date. Now I can find it (love your Plexi rigs). All good!

Quote from cmbrowns

Nuno Conde, they're on the Rig Exchange but the Create Date is back in 2018 so you may be sorted in a way where you don't see them. You can sort by Time Of Upload and they'd be near the top. Or just search for Diogo and you should find 213 rigs.

Thank you very much!

Hi Diogo, thanks fpor sharing your profiles.

Do you know why they don't show on Rig Manager?

Regards

Quote from CrazyShred

Hey everyone!

What the title says.........anyone experiencing the same issue as me?

I experienced it too, but I playd with the Kabinet on the floor, and did not take off the +4db bass compensation. I'll try it tonight again

Thank you all, for your time answering me!

All good!

Nuno

Hi there,

First things first, Merry Christmas to all!

I have connected my Mission Eng with the switch, that I use to activate the wha (block A). Everything works as it should.

The only issue, for me, is that to activate the wha I have to take the pedal to toe position, and the volume rises and to maximum that is set on rig menu (I use it as also a booster).

Is there a way (without using one of the effects button of the remote to activate the wha) to deal this "problem" and use the wha effect with this volume rise?

Sorry for my rusty English

Best regards from Portugal

Nuno

Hi,

Any discounts yet in 2022?

Regards

Quote from net99

Hi,

I have the same issue with OS 3.7.5 Public Beta.

Downgrade to OS 8.7.3.36999 seem to help.

No latency switching rigs after downgrade

Hi,

How can I find te file to also downgrade for the OS 8.7.3.36999 ?

Thanks in advance

Hi,

I would also like to have this option (pre and post amp with more effects).

Wondering if it is possible? (we have only 4 + 4 "effects" buttons)..

Will not be a hardware limitation? (or not, and they already thought about it)

Just my 2 cents

Quote from ST

Setting aside the Quick button for a moment, I knew that I had used autoassign at some point, but couldn't remember how. Also, searching the main manual 8.5 turned up nothing.

I figured it out and made some notes.

Auto Assign Effects Buttons to Remote

You can automatically assign the Stomps and Effects to the Remote buttons I, II, III, IV. It will assign Stomps/Effects from left to right. For example, if you have only three stomps, and two effects, auto assign will assign the three stomps and the first effect.

This only works if none of the buttons have been assigned.

On the Profiler

• Press the Rig Button
• Use the Page buttons to navigate to page [6/6]
• On the display, you will see "Press STORE to autoassign"
  If you don't see the message, one or more of the buttons has already been assigned. Note, you can clear the assignments with the Soft buttons above the display.
• Press the STORE Button

Display More

Thank you!!! Your notes are very usseful!!!!

Quote from paults

QUICK Button

This button can be configured to assume different functions, according to your preference. By default, the QUICK button returns to the most recently accessed module or section edit page. You can find more details of what functions are available in the Quick Functions chapter.

System Menu - Quick Function

On this page, you can determine the function of the QUICK button using the soft knob “Quick Function”. This function allows you to tailor the QUICK button as a shortcut to particular functions like the “Snapshot Browser”, returning to last page edited (“Quick Edit Page”) and simulating a Morph Button.

(Turn the soft knob to see the functions that can be assigned to the Quick knob. OS 8.7 adds the already existing "Auto-assign Remote switches I-IIII" function as an additional option for the Quick button.)

Display More

Hi,

Thank you very much for your explanation., but what I do not understand is if I set the quick button to Auto-assign Remote switches I-IIII what does it do? In my experience it does nothing, or I can't understand how it works

(Hope my English is fine for you to understand what I mean)

My best regards

Hi there,

Can you please help me understanding what is meant by the new quick button function (Autoassign I-IIII), and how it works? (i can't understand the 8.7 manual revision - last update)

Regards

Nuno

Hi,

Hope you are all good!

Yesterday, I deleted a performances folder on my rig manager, without wanted to do that. Did it unconsciously.

Do you know how can I recover that performances? (on my hard disk, where are they? - I can't find it on my trash basket)

Thanks in advance

Regards from Portugal

HI, are you offering Black Friday discount?

Regards